두 대의 라우터와 두 대의 컴퓨터가 있습니다. 네트워크에서 컴퓨터가 서로를 볼 수있는 것 같지 않습니다.
Router2 (Linksys BEFSR41 v3.1) 는 Router1에 연결됩니다 .
PC1 은 Router1에 연결됩니다 .
PC2 는 Router2에 연결됩니다 .
PC1 (Windows 7)은 PC2 (Windows XP)를 찾거나 볼 수 없습니다 .
둘 다 "WORKGROUP"이라는 동일한 WORKGROUP 이름을 갖습니다.
무엇을 제공합니까?
둘 다 동일한 라우터 ( Router1 )에 있으면 서로를보고 파일을 잘 공유 할 수 있습니다.
"서로보기"라는 말의 의미는 "네트워크"로 이동하여 다른 컴퓨터를 볼 수 있고 해당 컴퓨터를 클릭하고 공유 폴더를 볼 수있는 것과 같습니다.
예를 들면 다음과 같습니다
에 PC1 나는 "\\ PC2 \ MySharedFolder"을 입력 할 수 있도록하고 싶습니다 그리고에 MySharedFolder로 이동 PC2
[--------------- 해결됨 ---------------]
Special thanks to Edward and Ramrod for their help. It turns out that the WAN port (the internet feed port) on Router2 (Linksys) CANNOT be configured to hold traffic with DHCP disabled - meaning the internet feed ethernet cable MUST BE PLUGGED into one of the 4 LAN ports, not the internet feed port (also known by everyone but me as the WAN port). Due to my ignorance it took me a while to catch on to this.
As soon as I plugged the internet feed ethernet cable into one of the 4 LAN ports on Router2 instead of the WAN port, the Router2 automatically configured itself as a Access Point/Bridge/Switch/idk and allowed Router1 to assign the IP addresses (192.168.0.x) and now all the computers can successfully see each other on the network. Kinda weak if you ask me, the WAN port should be able to be used as a LAN or WAN, whatever I choose.
Concerning this, I went ahead and bought a NETGEAR N300 which DOES ALLOW you to put the internet feed into the WAN port and configure it as an Access Point (which I guess intern treats the WAN port as a LAN port instead). This allows you to support 4 additional computers instead of just the 3 additional ones the Linksys could only support in this setup (since one HAD to be used for the internet feed).
The first basic thing you can do is bring up a commmand window as well as browsers for your individual router admin page. When say you know the IP address of PC1 by typing ipconfig into the CMD window you can see your IP address, and needless to say this needs to be on the same network range as all your other devices (routers and PC2) to see them unless you know how to setup that connection on the routers to "Route" from one network range to another.
This is for if the router2 is connected to router1 through the LAN ports on both machines.
most of your internal devices I would say are on the 192.168.1.0 range.
As a possible solution have the Router connected to the internet setup for DHCP with an IP address of 192.168.1.1 and a subnet of 255.255.255.0 . Check PC1 is connected with that address as the default route in the CMD window with ipconfig. Next in the admin page for router2 make sure it has the default route setup as 192.168.1.1 with its IP as 192.168.1.2. Lastly in PC2 you can try and type Ping to all three of those IP addressses to see if it completes successfully.
After all that is done and you still have issues it may be because you need to type a double \ at the beginning of the url PC2\MySharedFolder
내 솔루션은 모든 것을 동일한 네트워크 IP / 서브넷 마스크 범위에 배치하는 것임을 명확히하고 싶습니다. 이것이 Windows 작업 그룹 공유가 실제로 작동하는 유일한 방법이라고 믿기 때문입니다. 그러나 나는 그것에 대해 틀릴 수 있습니다.
이 기사는 인터넷에서 수집됩니다. 재 인쇄 할 때 출처를 알려주십시오.
침해가 발생한 경우 연락 주시기 바랍니다[email protected] 삭제
몇 마디 만하겠습니다