D-link DSl-2750U 무선 라우터를 사용하여 친구와 인터넷 연결을 공유하고 있으며 네트워크 차량은 Atheros AR9285입니다. 최근 가끔 네트워크에 연결할 수 없습니다.
무엇이 문제일까요?
iwconfig는 다음과 같은 출력을 제공했습니다.
iwconfig
mon0 IEEE 802.11bgn Mode:Monitor Tx-Power=15 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Power Management:on
eth0 no wireless extensions.
lo no wireless extensions.
wlan0 IEEE 802.11bgn ESSID:"DLink"
Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated
Tx-Power=15 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Power Management:off
ifconfig는 다음과 같은 출력을 제공했습니다.
ifconfig
eth0 Link encap:Ethernet HWaddr 78:84:3c:e7:0f:5a
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:2458 errors:0 dropped:0 overruns:0 frame:0
TX packets:2458 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:172791 (172.7 KB) TX bytes:172791 (172.7 KB)
mon0 Link encap:UNSPEC HWaddr CC-AF-78-B3-E5-0F-00-00-00-00-00-00-00-00-00-00
UP BROADCAST NOTRAILERS RUNNING PROMISC ALLMULTI MTU:1500 Metric:1
RX packets:38404 errors:0 dropped:442 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:2671272 (2.6 MB) TX bytes:0 (0.0 B)
wlan0 Link encap:Ethernet HWaddr cc:af:78:b3:e5:0f
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:89 errors:0 dropped:0 overruns:0 frame:0
TX packets:185 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:22749 (22.7 KB) TX bytes:32983 (32.9 KB)
nm-tool은 다음 출력을 제공했습니다. n
m-tool
NetworkManager Tool
State: connecting
- Device: eth0 -----------------------------------------------------------------
Type: Wired
Driver: r8169
State: unavailable
Default: no
HW Address: 78:84:3C:E7:0F:5A
Capabilities:
Carrier Detect: yes
Wired Properties
Carrier: off
- Device: wlan0 [DLink] -------------------------------------------------------
Type: 802.11 WiFi
Driver: ath9k
State: connecting (configuring)
Default: no
HW Address: CC:AF:78:B3:E5:0F
Capabilities:
Wireless Properties
WEP Encryption: yes
WPA Encryption: yes
WPA2 Encryption: yes
Wireless Access Points
Chandu: Infra, AC:F1:DF:E8:31:09, Freq 2412 MHz, Rate 54 Mb/s, Strength 32 WPA WPA2
DLink: Infra, FC:75:16:D4:60:32, Freq 2412 MHz, Rate 54 Mb/s, Strength 15
더 많은 정보가 없으면 모니터 모드를 사용하지 않을 것입니다. 실행하십시오 :
echo "options ath9k nohwcrypt=1" | sudo tee /etc/modprobe.d/ath9k.conf
sudo modprobe -rfv ath9k
sudo modprobe -v ath9k
모니터 모드 사용을 고집하는 경우 다음을 시도하십시오.
echo -e '#!/bin/bash\n/sbin/iwconfig mon0 power off' | sudo tee -a /etc/pm/power.d/wireless
mon0에 대한 전원 관리가 꺼집니다.
해당 옵션이있는 경우 라우터를 wpa2 암호화로 설정하는 것이 가장 좋습니다.
연결이 가능하도록 나열된 두 네트워크 모두에서 신호 강도가 낮지 만 실행하라는 첫 번째 명령 세트는 일반적으로 어느 정도 도움이됩니다. 특히 벽이나 신호를 차단하는 무언가가있는 경우 연결할 수 있도록 라우터에 더 가까이 이동해야 할 수 있습니다.
귀하의 장치는 Linux 드라이버가있는 ar9285이며 내 경험으로 볼 때이 시리즈의 모든 장치 중 가장 나쁜 신호 강도를 가지므로 무엇을하든 라우터에서 멀리 떨어질 수 없습니다.
이 기사는 인터넷에서 수집됩니다. 재 인쇄 할 때 출처를 알려주십시오.
침해가 발생한 경우 연락 주시기 바랍니다[email protected] 삭제
몇 마디 만하겠습니다