Parrot 시스템에 드라이버가 설치된 USB WiFi 어댑터 (Edimax EW-7612UAn V2 )가 있고 컴퓨터의 pci가 parrot과 호환되지 않습니다. -ng usb wifi 어댑터가 잘 작동하고 컴퓨터의 pci는 물론 작동하지 않습니다. 내 pci를 모니터에 놓고 내 usb wifi 어댑터를 관리 모드에두면 usb 어댑터가 모니터 모드가 아니지만 네트워크 관리자가 wifi 메뉴에서 둘 다 제거합니다.
즉, 기본 pci가 호환되지 않거나 인식 할 수없는 경우 parrot은 두 어댑터를 모두 인식하지 못합니다. 그래서 앵무새가 USB 와이파이 어댑터 만 사용하도록 강제하려면 어떻게해야합니까?
lsusb -v 결과 :
Bus 002 Device 003: ID 7392:7822 Edimax Technology Co., Ltd 802.11n WLAN Adapter
Couldn't open device, some information will be missing
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x7392 Edimax Technology Co., Ltd
idProduct 0x7822
bcdDevice 2.00
iManufacturer 1
iProduct 2
iSerial 3
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 0x002e
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 4
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x84 EP 4 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 1
네트워크 관리자의 스크린 샷
rf-kill의 결과 :
0: hp-wifi: Wireless LAN
Soft blocked: no
Hard blocked: yes
1: hp-bluetooth: Bluetooth
Soft blocked: no
Hard blocked: yes
2: phy0: Wireless LAN
Soft blocked: no
Hard blocked: no
3: phy1: Wireless LAN
Soft blocked: no
Hard blocked: yes
ifconfig의 결과 :
eth0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
ether 34:64:a9:73:43:20 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 8 bytes 396 (396.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 8 bytes 396 (396.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
나는 대답을 찾았습니다. 여기 에서 지시를 사용하여 내 pci가 "rt2800pci"를 사용한다는 것을 발견했습니다. 다음 명령을 사용하여 모듈을 언로드했습니다.
modprobe -r rt2800pci
잘 작동하고 usb wifi 어댑터가 작동하기 시작했지만이 솔루션은 컴퓨터가 재부팅되면 한 세션에서만 작동합니다. 모듈을 다시 언로드해야합니다. 모듈을 항상 언로드하려면 모듈을 블랙리스트에 올릴 수 있습니다.
이 기사는 인터넷에서 수집됩니다. 재 인쇄 할 때 출처를 알려주십시오.
침해가 발생한 경우 연락 주시기 바랍니다[email protected] 삭제
몇 마디 만하겠습니다