ADSL2 +モデムとしてのみ使用するActionTecT2200Hモデム/ワイヤレスルーターのコンボがあります。Webインターフェイスからはブリッジモードが非表示になっていますが、telnetを有効にすると、ブリッジのオプションが見つかります。このCLIを使用してブリッジモードを設定するのに十分な知識がありません。モデムにログインすると、使用可能なコマンドのリストは次のとおりです。
> ?
help
logout
exit
quit
reboot
adsl
xdslctl
xdslctl0
xdslctl1
xtm
brctl
cat
loglevel
logdest
virtualserver
ddns
df
dumpcfg
dumpmdm
meminfo
psp
kill
dumpsysinfo
dnsproxy
syslog
echo
ifconfig
ping
ps
pwd
sntp
sysinfo
tftp
wlctl
arp
defaultgateway
dhcpserver
dns
lan
lanhosts
passwd
ppp
restoredefault
route
save
swversion
uptime
cfgupdate
swupdate
exitOnIdle
wan
gpv
mcpctl
これがのコマンドリストですbrctl
:
Usage: brctl [commands]
commands:
addbr <bridge> add bridge
delbr <bridge> delete bridge
addif <bridge> <device> add interface to bridge
delif <bridge> <device> delete interface from bridge
setageing <bridge> <time> set ageing time
setbridgeprio <bridge> <prio> set bridge priority
setfd <bridge> <time> set bridge forward delay
sethello <bridge> <time> set hello time
setmaxage <bridge> <time> set max message age
setpathcost <bridge> <port> <cost> set path cost
setportprio <bridge> <port> <prio> set port priority
enableportsnooping <bridge> <value> 0-disable 1-standard 2-blocking
enableproxymode <bridge> <value> To enable 1 or disable 0
show show a list of bridges
showmacs <bridge> show a list of mac addrs
addmacs <bridge> <port> <mac> add mac addresses to the bridge table
delmacs <bridge> <port> <mac> remove mac addresses from the bridge table
showstp <bridge> show bridge stp info
stp <bridge> {on|off} turn stp on/off
mldenableportsnooping <bridge> <value> 0-disable 1-standard 2-blocking
mldenableproxymode <bridge> <value> To enable 1 or disable 0
enableigmpratelimit <bridge> <value> 0-disable, 1..500-packet rate
wanのコマンドリストは次のとおりです。
> wan
Usage:
wan add interface <atm|ptm|eth>
wan add service <interfacename> --protocol <bridge|ipoe|pppoe|ipoa|pppoa>
wan delete interface atm <port.vpi.vci>
wan delete interface ptm <port> --priority <normal|high|both>
wan delete interface eth <ethx>
wan delete service L3IfName
wan show interface
wan show [<port.vpi.vci>]
wan --help <bridge|pppoe|pppoa|ipoe|ipoa>
そして、WANブリッジのコマンドリスト:
> wan --help bridge
Usage:
wan add service <L2interfacename> --protocol bridge
[--service <servicename>]
wan delete interface atm <port.vpi.vci>
wan delete interface ptm <port> --priority <normal|high|both>
wan delete interface eth <ethx>
wan delete service L3IfName
wan show interface
wan show [<port.vpi.vci>]
wan --help <bridge|pppoe|pppoa|ipoe|ipoa>
誰かがこれを設定するための正しい方向に私を向けるのに十分な情報を持っていますか?
これはあなたが考えている橋である橋に依存しています。コマンドの出力に基づくと、これはVLANを作成するための「ブリッジ」ツールであり、DSLから802.3へのブリッジ用ではありません。これらの設定はいずれもWebインターフェイスにある可能性がありますが、そうでない場合は、インターネットプロバイダーに電話して、モデムとしてのみ機能する設定を要求する必要があります。
この記事はインターネットから収集されたものであり、転載の際にはソースを示してください。
侵害の場合は、連絡してください[email protected]
コメントを追加